Elite 2
|
Capacity:
Speed:
Average Read Time:
|
1.79 GB
5400 rpm
11 ms |
|
ST-42000N Elite 2 Fast SCSI-2
Spindle Sync � �� Terminator Power Source (see below)�Ŀ
�4��1�Ŀ �������1 4o�o3 �������1 �
p�o oo A �ij����� 2o o1 ��ij���� �
o o o o o n�o oo B �Terminator SIPS� Power o o o o �
o o o o o ��������������������������������� �12�G�G�5Ŀ o o o o �
������������P�W�A��͵::::::::::::::::::::::::1��͵ 0 0 0 0 ����������� �
4 2 1 � � �������������������������; \���������/ � � � � �
����� � � SCSI Cable Connector � � � � �
� � � � � � � �
� � ��� Master off/Slave on - Spindle Sync � � � � �
� ����� Write Protect option enable � � � � �
��������� SCSI ID � � � � �
Spinup Delay (10 secs * ID) �� � � � �
Motor Start option enable ���� � � �
Parity check DISable ������ � �
Sweep Cycle enable �������� �
�
���������������������������������� �
� Terminator Power Source Options ������������������������������������������
����������������������������������������������������������������������Ŀ
� 2 & 4 � Initiator supplies power over the SCSI Bus for terminators. �
� Drive supplies no terminator power. �
� 1 & 2 � Drive supplies power for its own terminator resistor-paks �
� but not to SCSI Bus. This is the factory setting. �
� 1 & 3 �
� AND � Drive supplies power fpr external terminator at end of the �
� 2 & 4 daisy chain. Terminator resistor-paks must be removed. �
� This option is recommended only for last drive on daisy �
� chain. �
������������������������������������������������������������������������
T-RES descriptions: ST42000N 2 SIPs
ST42000ND 2 DIPs
ST-42000N
Elite 2
UNFORMATTED CAPACITY _____________________2,106,263,040
FORMATTED CAPACITY (512 byte blk) ________1,792,111,616
AVERAGE SECTORS PER TRACK ________________83
ACTUATOR TYPE ____________________________ROTARY VOICE COIL
TRACKS ___________________________________41,984
CYLINDERS ________________________________2,627/2,624 (user)
HEADS ____________________________________16
DISCS (5.25 in) __________________________9
MEDIA TYPE _______________________________THIN FILM
HEAD TYPE ________________________________THIN FILM
RECORDING METHOD _________________________ZBR RLL (2,7)
INTERNAL TRANSFER RATE (mbits/sec) _______30-40
EXTERNAL TRANSFER RATE (mbyte/sec) _______10 (burst)
SPINDLE SPEED (RPM) ______________________5,400
AVERAGE LATENCY (mSEC) ___________________5.55
COMMAND OVERHEAD (mSEC) __________________<0.5
BUFFER ___________________________________256 Kbyte
Read Look-Ahead, Adaptive, Multi-Segmented
Cache
INTERFACE ________________________________SCSI-2 FAST
BYTES PER TRACK __________________________42,000-55,440
SECTORS PER DRIVE ________________________3,500,218
BYTES PER CYLINDER _______________________672,000-887,040
TPI (TRACKS PER INCH) ____________________2,250
BPI (BITS PER INCH) ______________________41,713
AVERAGE ACCESS (ms) ______________________11
SINGLE TRACK SEEK (ms) ___________________1.7
MAX FULL SEEK (ms) _______________________22.5
MTBF (power-on hours) Class A Room _______250,000
MTBF (power-on hours) Office _____________150,000
POWER REQUIREMENTS: Single ended/Differential
+12V START-UP (amps) _4.6/4.6
+12V TYPICAL (amps) __2.0/2.0
+5V START-UP (amps) __2.3/2.6
+5V TYPICAL (amps) ___2.3/2.6
TYPICAL (watts) ______29.9/31.8
MAXIMUM (watts) ______33.7/36.6
WRITE PRECOMP (cyl) ______________________N/A
REDUCED WRITE CURRENT (cyl) ______________N/A
LANDING ZONE (cyl) _______________________Auto
USER MANUAL PART NUMBER __________________
OTHER ____________________________________
Synchronized Spindles, Sweep Cycle Capability
ZBR = Zone Bit Recording = Variable sectors per track
** Already low-level formatted at the factory with six spare sectors
per cylinder, one spare cylinders/unit, one system cylinder/unit, and
one diagnostic cylinder/unit.
Physical:
Height (inches/mm): 3.25/82.6
Width (inches/mm): 5.75/146.1
Depth (inches/mm): 8.0/203
Weight (lbs/kg): 7.8/3.6
Seagate reserves the right to change, without notice, product
offerings or specifications. (01/03/96)
|
