Seagate ST31230W Hawk 2LP HARD DISK DRIVE REPAIR, Seagate ST31230W Hawk 2LP HARD DISK DRIVE SPECIFICATIONS,
Seagate ST31230W Hawk 2LP hard disk drive sales, Seagate ST31230W Hawk 2LP hard disk drive repair, Seagate ST31230W Hawk 2LP hard disk drive specifications, 
Seagate ST31230W Hawk 2LP Hard Disk Drive Repair, Seagate ST31230W Hawk 2LP Hard Disk Drive Specifications, Seagate ST31230W Hawk 2LP Seagate ST31230W
Specifications



seagate st31230w picture.
seagate st31230w picture.
seagate st31230w picture.

Seagate ST31230W Specifications
Model Capacity Size Height Bus Type Int.Type
ST31230W Hawk 2LP 1060MB 3.5" SL SCSI2 W

Hawk 2LP   :    ST31230W
Hawk 2LP

Capacity: 
Speed: 
Average Read Time: 
 

1.01 GB
5400 rpm
10.4 ms



ST-31230W/WD/WC Fast Wide SCSI-2 (Hawk 2LP)

  �����������ͻ
  � REAR VIEW �  (ST-31230W/WD only)
  �����������ͼ
        (TOP)                   Auxiliary
          ___________________  ���  �1�/���������\
        �( �����������������1)ͳ::::::�� 0 0 0 0 ��
          \�����������ij����/  �  ��  ���5�G�G�12�
       68 pin I/O Cable�        ������
       Connection Male          ������
                                ������
                                ������
        Auxiliary option header ������
           pin-11 +5v  ���������ٳ����
           pin-10 GND  ����������ٳ���
           SCSI ID = 8 �����������ٳ��
           SCSI ID = 4 �����������Ĵ��
            or pin-6 REFIND+ ������ٳ�
           SCSI ID = 2 �������������ٳ
           SCSI ID = 1 ���������������
           SCSI ID = 0 (none)


  �����������ͻ
  � REAR VIEW �  (ST-31230WC only)
  �����������ͼ
                     80 pin I/O and DC Power Wall/bracket Connection
                     �  Female
    J1          /���ij���������������\      TOP (HDA)
     ����������/ �������������������� \����������
              (\�1������������������40/)    BOTTOM

     Notes on 80 pin I/O connector:
       pins  1 -  4 = +12v        41 - 44 = 12v GND
            34 - 36 = +5v         74 - 76 = 5v GND
                 37 = SYNC             77 = LEDC
                 38 = MTRON            78 = DLYDST
                 39 = SCSIA0           79 = SCSIA1
                 40 = SCSIA2           80 = SCSIA3

  Mating NC connector: AMP US p/n: 2-557103-1 straight-in, Male 80-pin
                                   2-557101-1 right angle to PCB

  �����������������ͻ
  � RIGHT SIDE VIEW �  (Both ST-31230W and ST-31230WC)
  �����������������ͼ


BACK   �͸       J2  12345678                    TOP (HDA)  FRONT
 OF    J1�����������������������P�W�A����������������������� OF
DRIVE  �;           ::::::::                    BOTTOM     DRIVE
                     ��������
   �Terminator Power ٳ������ Enable T-Res
  ڴTerminator Power �ٳ����� Start Delay (12 secs * ID)
  �         Reserved ��ٳ���� Motor Start
  �    Parity Enable �������� Write Protect
  �
  �
  � ��������������������������������Ŀ
  �Ĵ Termination Power-source Table �
    ����������������������������������������������Ŀ
    ������....�����....�����PWA edge�����          �
    �                                              �
    �  1 2     1 2      1 2                        �
    � �ķ       �ķ    ���ķ  A Drive Supplies Bus �
    � ���     ��    ����  B Drive Supplies Own �
    � ���     ���     � �   C Bus Supplies Drive �
    �   A       B        C                         �
    ����������Default�������������������������������
  Note: The model ST-31230WC drive cannot furnish terminator power,
because no pins on the 80 pin I/O connector are devoted to terminator
power.


  ������������ͻ
  � FRONT VIEW �  (Both ST-31230W and ST-31230WC)
  ������������ͼ


                      TOP (HDA)   J6  ������1�
     ��P�W�A�������������������������͵::::::��
                 *    BOTTOM          ������;
                 �                     ������
            LED ��                     ������
                                       ������
                                       ������
               Auxiliary option header ������
                  pin-11 +5v  ���������ٳ����
                  pin-10 GND  ����������ٳ���
                  SCSI ID = 8 �����������ٳ��
                   or pin-8 BUSY �����    ���
                  SCSI ID = 4 ������������ٳ�
                   or pin-6 REFIND+ ��     ��
                  SCSI ID = 2 �������������ٳ
                  SCSI ID = 1 ���������������
                  SCSI ID = 0 (none)

      If these ID jumper are used, then
         ID jumpers shown in left side view J5
         or 80 pin I/O cable ARE NOT USED.


                            ST-31230W
                            Hawk 2LP

       UNFORMATTED CAPACITY (GB) ________________1.28
       FORMATTED CAPACITY (xx SECTORS) (GB) _____1.06
       AVERAGE SECTORS PER TRACK ________________103
       ACTUATOR TYPE ____________________________ROTARY VOICE COIL
       TRACKS ___________________________________19,960
       CYLINDERS ________________________________3992
       HEADS ______PHYSICAL______________________5
       DISCS (3.5 in) ___________________________3
       MEDIA TYPE _______________________________THIN FILM
       RECORDING METHOD _________________________ZBR RLL (1,7)
       INTERNAL TRANSFER RATE (mbits/sec)________33.9 to 56.7
       EXTERNAL TRANSFER RATE (mbytes/sec)_______20 Sync.
       SPINDLE SPEED (RPM) ______________________5411
       AVERAGE LATENCY (mSEC) ___________________5.54
       BUFFER ___________________________________512 KByte
         Read Look-Ahead, Adaptive,
         Multi-Segmented Cache
       INTERFACE ________________________________SCSI-2 FAST Wide
                                                 ASA II
       TPI (TRACKS PER INCH) ____________________4200
       AVERAGE ACCESS (ms) (read/write)__________10.4/11.4
         Drive level with controller overhead
       SINGLE TRACK SEEK (ms) (read/write)_______2.1/2.5
       MAX FULL SEEK (ms) (read/write)___________20.4/21.4
       MTBF (power-on hours) ____________________800,000
       SHOCK (G's):
                operating (Read/Write) __________10
                nonoperating ____________________75
       ACOUSTICS (typ/max dBA) __________________/
       POWER REQUIREMENTS: +12V START-UP (amps) _2.0
                           +12V TYPICAL (amps) __0.35
                           +5V START-UP (amps) __0.61
                           +5V TYPICAL (amps) ___0.36
                           TYPICAL (watts) ______
                           MAXIMUM (watts) ______
       WRITE PRECOMP (cyl) ______________________N/A
       REDUCED WRITE CURRENT (cyl) ______________N/A
       LANDING ZONE (cyl) _______________________AUTO PARK
       IBM AT DRIVE TYPE ________________________0 or NONE

       Physical:
                        Height (inches/mm):     1.00/25.4
                        Width  (inches/mm):     4.02/102.1
                        Depth  (inches/mm):     5.77/146.6
                        Weight    (lbs/kg):     1.5/0.68

Already low-level formatted at the factory with 1 spare sector
per track and 2 spare cylinders/unit.

ZBR = Zone Bit Recording = Variable sectors per track

Seagate reserves the right to change, without notice, product 
offerings or specifications. (10/24/94)

All manufacturer's Names, Logos and trademarks are the properties of the respective manufacturer.


HOME Seagate drives All Hard Drives


Check our Media Store for all your Floppy Disk and Tape Supplies.


Contact us

Copyright © 1997 - 2011 Erv Fleckstein ( M. Farris & Associates ). All Rights Reserved.